سرار صيانة الطابعات

HP IIISi Printers:

Press ONLINE until the light goes off
Hold down MENU until PCL CONFIG MENU appears
Press the MENU key until SERVICE MSG=ON* appears
Press the + or - key to change display to SERVICE MSG=OFF
Press ENTER/RESET MENU key to turn message off, the * should appear, then press ONLINE
HP 4Si Printers:

Press ONLINE until the light goes off
Press MENU until CONFIG MENU appears
Press the ITEM key until SERVICE MSG=ON* appears
Press the + or - key to change display to SERVICE MSG=OFF
Press the ENTER key to turn message off, the * should appear, then press ONLINE
HP 5Si:

Press MENU key 4 times for CONFIG MENU
Press ITEM to display SERVICE MESSAGE=OFF
Press ENTER
Press ONLINE
HP 4000/4050/4100/5000 Printers:

Turn the printer off
Hold down the left side of the ITEM and VALUE +/- keys, turn the printer on and wait until RESET MAINTENANCE COUNT is displayed and then release the keys
HP 4500/4550 Printers:

Turn the printer off
Hold down the CANCEL JOB and SELECT keys and turn the printer on, then wait until the display goes blank and the three LED's come on
Press the right side of the MENU key, then press the SELECT key
You will enter SERVICE MODE after the normal test completes
Press the ITEM key until the FUSER MAINTENANCE COUNT appears
Press VALUE +/- to change to zero
Press SELECT to save
Press GO; the printer should return to READY
HP 8000/8100/8150 Printers:

Press the MENU button until the display reads CONFIGURATION MENU
Press the ITEM button until the display reads SERVICE MESSAGE = ON/OFF
Select OFF*
Press SELECT to save
Turn printer off
Hold the VALUE MINUS and ITEM MINUS buttons while turning the printer back on Hold buttons down until display reads RESET MAINT/COUNTand then release both buttons
HP 9000 Printers:

Turn the printer off
Press and hold the CHECK key
Power on the printer
Release the CHECK key after all three lights come on The display should read SELECT LANGUAGE
Press the up arrow until MAINTENANCE KIT is displayed, then press the CHECK key again and the maintenance kit count has been reset
HP Color LaserJet 4500/4550 Printers (TRANSFER KIT RESET):

Press the MENU button until the RESETS MENU is displayed
Press the ITEM button until TRANSFER KIT SELECT IF DONE is displayed
Press the SELECT button
HP Color LaserJet 4500/4550 Printers (FUSER KIT RESET):

Press the MENU button until the RESETS MENU is displayed
Press the ITEM buton until FUSER KIT SELECT IF DONE is displayed
Press the SELECT button
Press the GO button to return to READY
HP Color LaserJet 4600 Printer (IMAGE TRANSFER KIT (ETB) RESET):

After Maintenance is performed, the display should read NEW TRANSFER KIT =
Press the down arrow to highlight YES, then press the CHECK button to reset Or enter CONFIGURE DEVICE in menus, choose RESETS then RESET SUPPLIES, choose NEW TRANSFER KIT and select
HP Color LaserJet 4600 Printer (FUSER KIT RESET):

After Maintenance is performed, the display should read NEW FUSER KIT =
Press the down arrow to highlight YES, then press the CHECK button to reset Or enter CONFIGURE DEVICE in menus, choose RESETS then RESET SUPPLIES, choose NEW FUSER KIT and select
HP Color LaserJet 8500/8550 Printers (TRANSFER KIT RESET):

Press the MENU button until the RESETS MENU is displayed
Press the ITEM button until RESET TRANSFER LIFE COUNT is displayed
Press the SELECT button to reset, then GO to return to READY
HP Color LaserJet 8500/8550 Printers (FUSER KIT RESET):

Press the MENU button until the RESETS MENU is displayed
Press the ITEM buton until RESET FUSER LIFE COUNT is displayed
Press the SELECT button to reset
Press the GO button to return to READY

Turn off the power to the printer, Hold down both the "paper load/eject" and the "Ink cleaning buttons", whilst you turn on the power, when the "paper out" led is just flashing release both buttons, and then press and hold the "Ink cleaning button" for at least 15 seconds. Turn off the printer again, then turn it back on again and the printer will work fine again

Turn Printer off.
While holding down Enter and Menu keys, power the printer on.
You should see PCU Diag Mode displayed.
Hit Menu key 6 times till Counter Set is displayed.
Hit Enter key
Dev xxxxx displayed, left 3 numbers are blinking.
Hit (down triangle symbol) till numbers are 000.
Hit Menu key, right 2 numbers are blinking.
Hit (down triangle symbol) till numbers are 00.
Hit Menu key.
Drm xxxxx displayed, left 3 numbers are blinking
Repeat steps 7-10.
Dev tm xxxxx displayed.
Repeat steps 7-10.
Drm xxxxx displayed.
Repeat steps 7-10.
Life xxx displayed.
Life should be set to 005.
Hit Menu key.
TNL xxx displayed.
TNL level should be between 90-110, if you have problems, try changing TNL.
Hit Enter key
Counter Set is displayed.
Hold down Form Feed key and insert blank paper into manual feed slot.
You should get a beep confirming reset.
Power printer down and back up, you are done

Turn the printer off
Enter the Diagnostics Mode by holding down the READY and RETURN buttons while powering on the printer until the display reads PERFORMING SELF TEST
Select MAINTENANCE COUNT
Select RESET to return the count to zero
Press the RETURN button to return to the Diagnostics Mode main menu, then reset printer to return to normal mode
Optra S, 2420/2450/2455/3455

Turn the printer off
Enter the Diagnostics Mode by holding down the GO and RETURN buttons while powering on the printer until the display reads PERFORMING SELF TEST. When ready, the display will read PRINT REGISTRATION
Scroll to PRINTER SETUP and press the SELECT button
Scroll to MAINTENANCE PAGE COUNT and press the SELECT button
Scroll to RESET MAINTENANCE COUNT and press the SELECT button to reset the count to zero
Press the RETURN button to return to the Diagnostics Mode main menu, then exit Diagnostics Mode to return to normal mode
Optra T (all models)

Turn the printer off
Enter the Configuration Menu by holding down the SELECT and RETURN buttons while powering on the printer until the display reads PERFORMING SELF TEST. After the self test, the display will read CONFIG MENU
Press the right arrow side of the MENU button until MAINTENANCE PAGE COUNT is on the display
Press the SELECT button. RESET should be displayed
Press the SELECT button again to reset
Press the RETURN button to return to the Configuration Menu and press the left arrow side of the MENU button to exit the Configuration Menu
Optra W810

Enter the Configuration Menu by holding down the SELECT and RETURN buttons while powering on the printer until the display reads PERFORMING SELF TEST. After the self test the display will read CONFIG MENU
Press the right arrow side of the MENU button until MAINT. COUNTER is displayed
Press the SELECT button, then scroll to RESET TRANSFER or RESET FUSER and press the SELECT button again to reset
Press the RETURN button to return to the Configuration Menu and press the left arrow side of the MENU button to exit the Configuration Menu
Optra C710

Enter the Configuration Menu by holding down the SELECT and RETURN buttons while powering on the printer until the display reads PERFORMING SELF TEST. After the self test the display will read CONFIG MENU
Press the MENU button right or left until RESET FUSER COUNT appears
Press the SELECT button to reset the count
Optra C720

Enter the Diagnostic Menu for all resets by pressing the GO and RETURN buttons and turn the printer on
Continue holding until PERFORMING SELF TEST is displayed
Select RESET COUNTERS from the Diagnostic Menu
Select the individual counter for reset and press the SELECT button
Optra C750

Enter the Configuration Menu by holding down the SELECT and RETURN buttons while powering on the printer until the display reads PERFORMING SELF TEST. After the self test, the display will read CONFIG MENU
Select individual reset for fuser or ITU kit
Optra SC 1275/Color 1200

Turn the printer off
Hold down the GO and RETURN keys while powering on the printer until PERFORMING SELF TEST is displayed
When REGISTRATION is displayed, press the right side of the MENU key six times until MAINTENANCE is displayed
Press the SELECT button, and then press the right side of the menu button to scroll to 80 or 81 RESET
Press the RETURN button until the display reads MAINTENANCE
Press the right side of the MENU button until the display reads EXIT DIAGNOSTICS
Press the SELECT button to return to the normal mode